Gap above integrated Washing Machine
Hi, Am leveling up new base units and integrated appliances. Base units at lowest point have 160mm plinth gap. I have come to the integrated dish washer next to integrated washing machine. Legs on...
View ArticleIkea EKBACKEN worktop 635*28*2460
Hi there,Has anyone fitted an EKBACKEN square edge worktop 28mm,as I would like to know if the worktop has the front and back edges sealed, as the display in the showroom looks like the rear edge is...
View ArticleAlusplash install in kitchen
Hi. Is there a shortage of alusplash fitters? I’m looking for fitters in London for 3 months now :-( Don’t know how to do it myself sadly.
View ArticleRGBW LED strip
Can anyone here recommend some reliable RGBW LED strips at a reasonable price for installing in a kitchen. 120 & 60 LEDs per metre if possible. They do not need to be IP rated. Thanks.
View ArticleBad kitchen worktop joint
Hi I’ve got a laminate worktop in my kitchen with a joint in the corner that has come apart, so there’s now a small gap. It’s not really bowed luckily, so I’m wondering what the best way to fix it is....
View ArticleAligning integrated dishwasher
Hello All A thought just occurred to me that the dishwasher is 600mm deep but the carcass units are only 560mm. The instructions that came with the kitchen (diykitchens) say that the units don't need...
View ArticleRecommend me where to buy a kitchen online
I know it has been asked before but seeking up to date recommendations on where to buy kitchen units & doors online. Can be the same place or a doors only place. TIA
View ArticleHafele hinge - 85 degree angle restrictor
I have these Hafele 110 degree hinges on some cabinets I have just fitted that hit the wall when fully open; does anyone know if these angle restrictors will fit? In the product info it says they are...
View ArticleRecess sink into wooden worktop
I've got a solid wood worktop, and a stainless steel sink with a lip that sits on top of the worktop. This is fine except water often pools between the sink and the wall which I'd like to solve. Often...
View ArticleNeed some advice on Kitchen Fitters Sundry items
I recently got someone to quote me on fitting a Wrens kitchen, these come fully built. He gave me a number of days to fit. The job went relatively slowly and some days was a struggle to see what he had...
View ArticleHelp or advice on unit height setting
Hi I am a novice I've ripped my whole kitchen out and started from scratch. My units have been made and are 725mm from bottom to top carcass and doors/draws made to match. Now I have set the units to...
View ArticleStainless Steel Backsplash Adhesive
Hi all, Doing a small DIY project in the kitchen and i have a Stainless Steel Back splash to install as well as Stainless Steel up stands that im planning to fix to the wall. Any recommendations as to...
View ArticleScribing the head of a larder unit into pitched roof
Hi guys, I have a job coming up with 2 handmade larder and a bridge wall unit inbetween them... They all weigh a ridiculous amount but the problem being that it hits the pitch of the ceiling. My...
View Articlewho is liable for damage
HI All, I have a bit of an issue at hand. The story goes like so, This customer wanted me to take on the works to supply and fit a kitchen and redecorate a full house. In the end he only gave me the...
View ArticleBase units going out 30-40mm on 4.5 run - acceptable?
Hi, Am fitting kitchen base units in L pattern. Short run is 1.8m, long run is 4.6m My walls are not square, and I think I made the mistake of fitting the short run first (which is parallel to its...
View ArticleRemoving carcas without disturbing worktop?
Hi all, I'm sure this is a fairly basic question to some of you, but please bear with me, I'd be very grateful for some pointers and your expertise. I recently bought a new build flat. It's clearly...
View ArticleInduction hob scratched
Hello Apologies if this does not belong here. We have had a new Bosch induction hob fitted and bought one pan just to try it. Used it very lightly for a couple of days and it’s already scratched!...
View Articleplinth in the way
So, I'd like to fit an end panel inbetween two integrated appliances. I'd obviously like the end panel flush with the doors but the floor level steps down to floorboards just after the plinth so I...
View ArticleKickboard
Hi Can anyone please tell me what is wrong here as the kickboard doesn't look right to me and the panels come to far forward. Thank you
View ArticleIntegrated washing machine door fitting
Hi everybody, I have a hinge kit for my integrated washing machine which I am about to fit. Machine is: Hoover HWB 814 DN1 (I think machine is also badged Candy.) Kit is: 41026810 It came without...
View Article