Clik here to view.
Cabinet oven 18mm carcass fit issues?
I am struggling to work out how a Bosch built in oven will fit exactly into my tall cabinet which will house the oven and a microwave/oven above which will have 18mm thick carcass panels. From......
View ArticleFitting Kitchen Units to a Solid (Breeze Block) Wall
Hi, I was wondering if someone could please give me some advice. I am trying to fit some Kitchen wall & base units to a solid breeze block wall. I've looked at some of the previous threads on here...
View ArticleB&Q Kitchen Cabinet Door Hinges - What are the best to buy?
Good morning, I'm using 3 x 800mm B&Q Wall Unit carcasses stacked on top of each other to build a cupboard on the landing and I'm mightily confused about buying suitable hinges. The last time I...
View ArticlePneumatic support failed
Hi everyone I seem to have a situation where are my cupboards the pneumatic support seems to a failed and doesn't offer a a cushion anymore is there any way to repair them or or are they simply a write...
View ArticleGas/ piping cut out in kitchen cabinet
Hi all, I am not a fitter but am starting my kitchen refurbishment next week. Whilst emptying my cabinets today, noted this gas/ pipe cut out through the carcass. Could any of you tell me what these...
View ArticleWhere to fit vent in kitchen
Hello people Hope your all well and safe My gas oven was releasing too much Carbon monoxide so had to be turned off found out was faulty got a replacement . The gas engineer said I need to get better...
View ArticleFitting Kitchen worktop in U shape kitchen
Hi, I've been fitting my own kitchen and about to proceed to worktop next week. All base units are levelled front and top. I’ve made a cardboard template for the longest run (piece (A) in photo) which...
View ArticleQuality Kitchen Laminate Worktops
Hi all, I'm looking for recommendations for good quality laminate kitchen worktops. I'm in the process of planning a new kitchen, and will most likely be buying the units from DIY-kitchens.com and will...
View ArticleWestmoreland Slate Crack Repair
Hi all, I have some stone (20mm thick Westmorland slate ie green) kitchen worktops to repair - the substrate was not up to the job and has differentially moved, cracking the tops in several places at...
View ArticleWall Cabinets Height
Is there a standard height between the top of the worktop to the underside of the wall cabinet? Thank you for your reply's in advance.
View Article70cm Gas Hob into existing 60cm worktop hole
I apologise now if this has been asked before - I did try to search but nothing came up. I'm hoping to get a 5-burner gas hob to replace my existing 4-burner hob. I realise the 5-burners are wider, but...
View Articleinfill at side of appliance
I have an 80mm gap at side of integrated appliance do i make infill 80mm or make 2 at 40mm either side?
View Article620mm worktops and old(ish) jig... Help!!
Hi all, I went to fit replacement worktops today, where the customer has bought their own from B&Q, who’s worktop range (I found out for the first time today) is now all 620mm. A quick bit of...
View ArticleAlusplash install in kitchen
Hi. Is there a shortage of alusplash fitters? I’m looking for fitters in London for 3 months now :-( Don’t know how to do it myself sadly.
View ArticleRoller shutter unit - whom to call?
I have a tall roller shutter unit on the kitchen which got stuck. I cannot open it more than 30 cm and then it rolls down (photo attached) so I cannot access the shelving behind it. The kitchen is 11...
View ArticleKitchen Fitter Required - Kent
Hi Looking for a kitchen fitter. Existing kitchen has been removed. Walls need tidying up prior to installation. Smallish galley type kitchen to be installed. Happy to discuss planning suggestions....
View ArticleDishwasher door seal
Hi, the black rubber seal on the bottom of my integrated dishwasher has come lose again, last time someone repaired it they used an adhesive to fix it in place but I’m not sure what. What...
View ArticleDIY bodge?
Hi, we’ve just bought a house and having a rewire and new boiler fitted. As they’ve started taking back the plasterboard in the kitchen it seems the plaster on the original wall is pretty basic with...
View ArticlePush Close/Open on Kitchen Carcasses
Good afternoon, I'm using B&Q 800mm cupboard carcassess to build a landing cupboard - 3 stacked on top of each other. I want to use, and have bought, some push-push catches. It looks to me like...
View ArticleWill this sink be Ok?
My kitchen is due to be delivered w/c 25th April (from DIYK); I'm planning to get Granite worktops professionally fitted (630mm wide & 30mm thick) from this company:...
View Article