Repairing Plaster after removing tiles.
Hi, I am in the process of removing an old backsplash from my kitchen. However when removing the tiles I noticed that quite alot of plaster was coming off with the tiles. I have attached some photos to...
View ArticleDo modern washer/dyers vent out the waste pipe
Hi Do modern washer-dryers vent out from the normal flexible waste outlet? Planning a new kitchen install and want to replace the washing machine with a wash-dryer due to space (no space for a separate...
View ArticleFridge problems
Hi So we recently moved and the new house has a built in fridge and we also bought the Beko Fridge Freezer off the previous owner. As seems to be far for the course so far, suddenly both seem to have...
View ArticleSimple question - which tile adhesive?
An overly simple question I think. I'm having tiled 8sq m of kitchen wall with 200mm x 100mm white 'Metro' tiles. I have tiled before and successfully used Mapei. (It was a recomendation from this...
View ArticleInduction hob installation
We've bought a Samsung induction hob and the installation guide says we need to install an insulation panel between the oven and hob. I called Samsung to find out what this panel is and they said they...
View ArticleWhich Silicone for Washing Machine Base?
Hi all, I'm a newbie poster so please go easy on me. I'm looking to use a cut out of worktop as a base for a washing machine to stand on. As luck would have it (not) the machine spans some old and new...
View ArticleIntegrate dishwasher - sliding hinge
I would be grateful if someone can confirm I am thinking correctly on this. Looking at the AEG FSB41600Z integrated dishwasher with "sliding hinge". It is described as: "This model has a sliding hinge....
View ArticleCutting this extractor hood shorter
Hi Guys, I'm looking at purchasing the following extractor hood (Luxair curved glass island Cooker hood 90cm black): https://www.tlc-direct.co.uk/Products/CH90CVDslashISLslashBLK.html The issue I am...
View ArticleClearance between dishwasher and worktop
My kitchen is being fitted. Was wondering if a 45mm gap between the bottom of the worktop and the top of the dishwasher is acceptable. I think it is too big and doesn’t look very good. Opinions would...
View Articleworktop advise. Help
hi. I have just ripped my Kitchen out. floor is back in and unit to. I'm about to fit the worktop sink ect. issue. the 600mm deep worktop does not fit flush on the wall as there is a pipe that is in...
View ArticleWhat edging strip for 4mm thick tiles?
Another simple question I'm afraid. I've asked Screwfix support for help, but they have not responded. I am fitting 'Metro' tiles. These are 6mm tick and the edges taper to 4mm thick. I am looking for...
View ArticleCornice and pelmets
Hi all Any tips for mitre jointing traditional decorative cornice and pelmets over 5 inches tall . Really struggling getting my 45s spot on . a knack on here from a pro would be very much appreciated ....
View Articlewhat brand router cutters for laminate worktop
What router cutters do most use for laminate worktop. Are the Screwfix Erbauer any good (a bit cheaper) Or best to stick with the Trend ones....
View ArticleLaminate Thickness?
I made a corner worktop and supports, which I now want to fix to the wall. Later I want to put in laminate flooring, so will put in spacers under the feet. How thick should I make the spacers to allow...
View ArticleSquare edge laminate - butt join or mitre join?
Hi going to fit square edge laminate worktops. Would you butt join the squared edges together or cut a mitre (worktop jig)? I've seen both methods in showrooms. Butt join seems harder in some ways as...
View ArticleWorktop fitting plates
I bought the stretcher plates from screwfix for fitting my wooden worktop onto my units. The bloody things arent square however, is there a reason for this or do i need to go to b&q and pay triple...
View ArticleSolid laminate worktops
Whats to watch out for with these tops. Have been looking at previous threads like https://community.screwfix.com/threads/zenith-solid-laminate-worktop.184077/page-2 I understand the zenith is around...
View ArticleIkea EKBACKEN concrete laminate worktop
Anyone recomend a colourfill code for the above worktop.
View ArticleHow to become a kitchen fitter
Hi this is my first post so please go easy. I have just finished a kitchen fitting course and wonder how I can get into this line of work full time and will my age go against me I and 43 I have all my...
View ArticleBuilt in Appliances
Hi all, Looking for some advice. I am currently installing my kitchen, and I’m looking to sit a built in microwave on top of a built in warming drawer. They sit together really nice alongside a built...
View Article