Bulb for Rangemaster cooker hood
Hi I’m struggling to source a bulb for a rangemaster cooker hood.. it’s only been fitted for 2 weeks and bulb flickering already, but bought (new) via eBay months ago, so no warranty. The bulb looks...
View ArticleClik here to view.
Best glue to stick laminate on worktop cut ends?
Any thoughts? I'm inclined to use EvoStick impact adhesive. I know it will need positioning carefully as it's put on as no way of getting it off but my experiences with it is that it will never come...
View ArticleHanging heavy screen from tiled walls. How to fix?
Technically a bathroom question but I need to hang a very heavy bath shower screen from a solid wall which has been tiled with expensive travertine tiles. I'm concerned that the supplied fixings (wall...
View ArticleMIR-CS-12 routing machine
Anyone came across this machine? Can't find anything about it.. Any good? View attachment 30151
View ArticleClick LVT under door....
I really should be paying a pro to do this to save time, stress and my knees! Anyway, Polyflor Loc is the floor and my challenge is how in the hell do I get this cut under the frame and clicked in. I...
View ArticleFitting Cabinet lighting to cabs
Hi, I've bought these for my cabinets https://www.screwfix.com/p/sylvania...Vxp3tCh1QUQ5vEAYYASABEgLQnPD_BwE&gclsrc=aw.ds I'll be honest i've only browsed at the install kit, but I'm a bit...
View ArticleWorktop joint expertise please...
Hi. I have fitted a U shaped kitchen with a return on one side of the open end (so more 90% of a rectangle really). I intend to fit 40mm square edged beech worktops using butt joints. I have a few...
View ArticleHowdens and Screwfix
I read a very interesting article this week about how the former boss at Screwfix is now shaking up Howdens. It was one of those 'you've read that so now see this type links' on Google but it was...
View ArticleSkinflint worktop question
Hi. As per previous thread I'm fitting a U shaped kitchen with a return peninsula at the open end making it almost a full square. the peninsula and the right hand wall are shallow depth. Peninsula...
View ArticleBenchmarx kitchen
I wonder if you could help please, I had a benchmarx kitchen fitted 14 mths ago i noticed at the time on one of the 100cm wallcupboards, both doors did not fit correctly.Anyway i thought nothing of it...
View ArticleWhat glue to use on worktop mitre joints ?
Is ColorFill a decent adhesive to use? I notice that they say 1 tube per 600mm worktop but not sure if that means 2 joints per tube or just one. They show it just being used near the top edge of the...
View ArticleJigsaw blades ??
I want to curve the end of a run of worktop and wonder about using a jigsaw first and then routing to finish it off. Any ideas about the best blade to use ideally actually in stock at screwfix? I'll...
View ArticleCutting Alusplash
Hi guys, I am looking at installing Alusplash panels in the kitchen Part of this will involve some cuts which (as they will be visible) I want to get spot on. Looking on the Alusplash site it says to...
View ArticleOak Worktop Oil - suitable for doors too
Is there a osmo oil which is suitable for doors and worktops? I see a lot of danish oil being advertised by worktop manufacturers but understand osmo oil is usually better?
View ArticleSealing worktop
Hi I've a 'belfast' sink to install that will stand higher than the worktop and further forward than the base unit doors. Best method of sealing the cut laminated worktops at each side? Was thinking of...
View ArticleButler sink & laminate worktops
Been asked twice in the last few weeks to fit a butler sink into laminate worktops, I steered clear as I can't see how it can be done. Has anyone done it and what did you do to the edges to keep the...
View ArticleCooker hood recirculating
Hi, quick question as I can't seem to find a conclusive answer on Google... I am putting up an extractor hood above my gas cooker. It will be a recirculating affair rather than outside ventilation. The...
View ArticleWorktop mason joint - change male into female?
Hello all I have a worktop with mason joint thats starting to fail next to a sink. Looks like it was just superficially sealed with colorfill on the top of the joint. I'd like to avoid replacing both...
View ArticleBeko integrated FF - Ventilation
Hi all, After while and milk going off I've noticed the FF isn't cooling below 10 degrees. Beko instructions are as generic as you like and doesn't mandatory state whether it needs a vent but from...
View Article