60 CM integrated cooker hood - uuf0360-2
Hi there, We recently got a new kitchen fitted, and this extractor fan was put into place, however when the fan is switched on it blows air out instead of sucking? The fitter said it was installed...
View ArticleHardboard not good enough for vinyl floor?
Wanting to have vinyl floor on our 3m x 3m kitchen suspended timber floor. The original floorboards were not bad, but draughty, so we decided to put 3mm hardboard down first. The entire floor has been...
View ArticleWren drawers removal
fitting wren kitchen anybody know how to remove drawer boxes from runners Old runners were easy pull out and lift but these are supposed to be new design Can't suss it out thx
View ArticleWhich screws for base cabinet to wall using space plug?
Hi, I thought I'd use space plugs to attach my cabinets to the wall rather than angle brackets. They come with a 6mm drillbit so red wallplugs are suitable and 8-10 ga (4-5mm) screws. The cabinet rail...
View ArticleClik here to view.
Replacing built in under-workstop oven with larger unit
I'm at my mum's for the weekend and her oven died on her yesterday, so we picked up one on ebay this morning. The old unit was a single oven, built-in, under-worktop. The new one is also under-worktop,...
View ArticleAm I to cheap?
just done a kitchen fit 5 base 1 larder 6 wall units integrated washer dishwasher fridge did all plumbing 2 masons sink hob etc fitted all panelling between worktop and wall units boxed round boiler...
View ArticleAdvice: New career.
Hey guys, looking for advice starting a new career as a kitchen fitter through a 10 week intensive course. (I know what your thinking already please bear with me) Okay some background info. When I left...
View ArticleExtractor Hood required for STEAM extraction
Hello, I bought and fitted this hood from Screwfix: http://www.screwfix.com/p/chx90ss-cooker-chimney-hood-stainless-steel-900mm/94753 To cut a long story short when the motor is running and there are...
View ArticleJig for 50mm Square Edge Laminate
Hi guys, First time posting on a forum. Have 3 worktops and a breakfast bar to join. All are 50mm thick square edge laminate (like picture) Wickes 'Romantic Walnut' wood effect and haven't fitted any...
View Articlekitchen lighting
Just had bought and had delivered some aluminium led profile lightning to fit under my kitchen cabinets, what would be the best way of affixing this to the underside of the cabinets, dont reall fancy...
View ArticleKitchen Worktop Restoration
I have old wooden kitchen worktops. I was wanting to have a laminate surface on top so it's a smooth and easy wipe clean surface. At the moment liquids soak into the wood and some areas of the worktop...
View ArticleShopfitters / High Quality Kitchen Fitters Needed
Subcontract installation teams needed for school furniture fit out projects across the UK but particularly Hertfordshire, Berkshire, Scotland and South Wales. Must be cscs carded and able to pass a...
View ArticleExtractor ideas please...?
Hi all, I am new to the forum and said hi to all earlier, hello again to all... I need to ask for help. We are currently having an unfinished extension completed. However, we are having an island put...
View ArticleSplashback
My daughter has bought a stainless steel splashback to go behind her electric hob.What silicone would you recommend for holding this in place.thanks in advance
View ArticleSanding joins in new oak worktop
Ive just installed a brand new oak worktop with units in my kitchen, a big DIY job. first time ever fitting a kitchen or working with oak worktops. Did as much research as i could before starting and...
View ArticleMaximum loading for a kitchen wall cupboard
Last week I fitted a 600mm corner wall unit as part of my refurb. project. With similar projects, I've always had a lovely "plaster over solid brick" wall to plug for the fixings. The current wall is...
View ArticleWhat are the correct plugs & screws for kitchen wall unit brackets?
Hi, Can anyone help me please with which plugs and screws to buy for the kitchen wall brackets, to fit onto a brick wall, these are the brackets I've got that came with the kitchen units on the link...
View Articleuser manual help please
hi my father has just bought a 2nd hand performance power tools radial arm mitre saw (pp250ms model no.) and i need to get a copy of the user manual for him can any one here help (or if you have one...
View ArticleWren Worktop
Has any one advice on Wren worktop with a stainless steel edge,can these be mitred in the standard way with a jig,if so what cutter is used I have fitted laminate tops before and mitred them using a...
View ArticleOver- hob extractor - what are the standard diameter(s) for the ducting?
Just nearing the end of a kitchen refurb. Tried to fit the extractor (a CST61) but the spigot for connecting to the ducting system is 115/118mm diameter (bendy plastic!). This doesn't seem to match...
View Article